Benutzer-Werkzeuge

Webseiten-Werkzeuge


en:e-642

E-642: Telefunken E 149 Uk/1

E-642, Telefunken E 149 Uk/1; developed and produced by Telefunken, Ulm.

The VHF receiver Telefunken E 149 Uk/1 carried the Army designation E-642, seven sets were purchased for the „EKF“ (Electronic Intelligence).

E-642 / Telefunken E149 Uk/1

Technical Data

Power Supply

Dimensions

  • 550 x 202 x 384 mm, 40 kg

Accessories

E-642 / Telefunken E149 Uk/1

Operation

The Telefunken E 149 Uk/1, which was used in the Swiss Army under the designation E-642, was developed around 1957 and acquired in 1960, seven receivers have been purchased for use of the „EKF“, the electronic intelligence service.

The 16 tubes single conversion superhet consists of a tuner insert (RF unit), with the frequency determining parts and the E 148/149 basic unit, in which the IF 10.7 MHz is processed.

In the middle of the front panel, the frequency-determining insertion is located. In case of the E 149 this is the 65 - 175 MHz unit. With the switch „1.Oszillator“ the set can be set to crystal controlled fixed frequency reception or VFO operation, in the frequency dial window, the reception frequency is displayed with an accuracy of at least 50 kHz.

The mode selector switch is located on the left of the front panel; in the positions „A1 / A3 Hand“, the RF gain can be set manually. At the top is the switch for the low-pass filter.

On the right you will find the volume control (AF control), which is combined with the power switch, the switch to set the measuring instrument to indicate the RF or AF line level and below the monitor speaker.

Technical Principle

Blockschaltbild Telefunken E148 UK/1
In the E-642, the tuning unit 65 - 175 MHz is used, the entire frequency range is covered in one band.

After two tuned HF preamplifier stages (EF800, EF80), the signal is converted to the intermediate frequency of 10.7 MHz in the mixer E88CC. The oscillator signal can either be derived from the tunable VFO (EF80), a quartz oscillator (operating frequency + 10.7 MHz) or an external high stability oscillator.

In the basic unit, the IF of 10.7 MHz is amplified in six stages (all EF80), the IF bandwidth is +/- 12.5 kHz.

After this, the signal is forwarded for demodulation, in AM (A3) mode, a semiconductor diode is used, for CW reception (A1) a BFO (E88CC) is switched on, in the FM (F3) demodulator one E88CC each works in the limiter and discriminator stage.

A further E88CC is used in the AGC amplifier and in the AF output stage, in addition to the speaker there are connections for the headphones, an 10.7 MHz IF output and a broadband IF output to connect the panoramic display PaG148 directly.

The set operates on mains voltages of 110 - 240 V, which are stabilized (STV150/30).

Valve setup

V1 (EF800, RF preamplifier); V2 (EF80, RF preamplifier); V3 (E88CC, mixer stage); V4 (EF80, oscillator); V5 - V10 (six EF80, 1st - 6th IF amplifier stage); Gl.diode (semiconductor diode, demodulation); V11 (E88CC, BFO); V12 (E88CC, FM Limiter); V13 (E88CC, FM discriminator); V14 (E88CC, AGC amplifier); V15 (E88CC, AF output stage).

Development

Field use

The Telefunken E 149 Uk/1, which was used in the Swiss Army under the designation E-642, was developed in around 1957 and acquired in 1960; seven receivers were used for the „EKF“ (electronic intelligence) services.

Manuals

Additional information

en/e-642.txt · Zuletzt geändert: 2019/04/07 20:28 von 127.0.0.1